Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Port St. Lucie Homeowners
Chimney repair in Port St. Lucie usually starts with something a homeowner can see and can’t explain: a stain on the ceiling near the flue, a cap that’s gone missing after a storm, mortar crumbling at the crown, or water that shows up inside the firebox long after the rain stops. We inspect before we sweep, and repair what we find. Our technicians have up to 11 years of experience, and we come to that inspection with a camera and a written report rather than an upsell. Nothing gets recommended that you can’t see for yourself, and we tell you plainly when a repair can safely wait.
One company handles the whole chimney here, so the diagnosis and the fix don’t get handed to a stranger. Call (844) 990-3838. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Same-day service is available when the schedule allows.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a screened cap over the flue opening to keep rain, animals, and debris out of a chimney that has no protection on top. You need one when the flue is open to the sky, when birds or squirrels have found their way in, or when sparks landing on the roof are a worry. We fit caps sized to the actual flue, not a generic cover, and we work with Gelco and Olympia Chimney components where the make and fit call for them. A typical cap installed in Port St. Lucie runs roughly $150 to $450 depending on the number of flues and the material, with the written estimate setting the final price.
Stainless and Copper Caps
Stainless steel holds up well against the summer rain this area gets, and copper gives a lower, quieter profile on the roofline. Both are made to fit a measured flue, and both are screened to keep wildlife out without restricting draft. We’ll tell you which suits your chimney rather than which costs more.
Multi-Flue and Custom Fits
A chimney with two or three flues needs one cap built for the whole footprint, not three separate covers sitting beside each other. We measure the crown and the flue spacing before ordering so the cap settles flat and sheds water away from the masonry. Custom-fit caps take a little longer to source but solve the problem once.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the removal and re-fitting of a cap that has rusted through, blown loose, or been damaged by a falling branch. You need it when the screen is torn, the top is bent, the mounting is no longer holding to the flue, or the cap has started to tilt and let water run down the inside of the chimney. We pull the old cap, check the flue tile it was mounted on, and fit a replacement from the same product families we trust for installation. Replacement in Port St. Lucie typically runs $175 to $475 depending on the cap size and whether the flue top needs any repair first. The written estimate sets the final price.
Why Caps Fail Early
Most premature failures are mounting failures, not metal failures. A cap screwed loosely into a cracked flue tile will move in wind, widen the crack, and eventually let go. We check the flue tile and the crown before we mount anything new.
Reusing Sound Hardware
If the cap is still sound and only the screen is torn, we’ll repair the screen rather than sell a whole new cap. The goal is a chimney that’s protected, not a bigger invoice.
Chimney Liner Installation
Chimney Liner Installation is fitting a new flue liner inside the chimney to contain heat, combustion gases, and creosote where the original clay tile has cracked or was never adequate for the appliance. You need it when the tile is cracked or missing, when a wood stove or insert has been added and the flue is now undersized, or when a camera inspection shows gaps that let heat reach the framing. We install DuraFlex liners for serious structural and draft problems that cleaning alone can’t fix, and we reline a flue only after showing you the evidence on camera. Liner installation in Port St. Lucie generally runs $2,200 to $5,500 depending on flue height, liner type, and whether the old liner needs removal. The written estimate is the final word.
Insulated Liners and Draft
An insulated liner keeps flue gases hotter, which means less creosote condenses on the walls and the chimney drafts more reliably on a cool morning. On a short or cold-running flue the difference shows up quickly. The liner swap is a skilled job; it isn’t something to attempt from a ladder.
Matching the Liner to the Appliance
The right liner size depends on what you’re burning in, not on what fits through the flue easiest. We size it to the appliance and to the chimney’s height and draft behavior. Getting that wrong is why some relined chimneys still smoke.
Chimney Flashing Repair
Chimney Flashing Repair is the repair or replacement of the metal and sealant where the chimney meets the roof, the joint that keeps rain from running down alongside the masonry and into the house. You need it when you see staining on the ceiling or the chimney breast, when the flashing is lifted, rusted, or sealed with tar that has cracked, or when water gets in even though the roof itself looks fine. We open up the joint, replace the flashing in a way that sheds water correctly, and check the surrounding shingles while we’re up there. Flashing repair in Port St. Lucie usually runs $250 to $850 depending on how much of the roof line has to be opened and reworked. The written estimate sets the price.
Signs Water Is Coming In
Brown stains on the ceiling near the flue, damp masonry after a storm, or efflorescence on the chimney’s outside face are the common tells. They point to the joint before they point to the crown about half the time.
Why Tar Patches Don’t Last
A tar patch may hold for one rainy season, then crack as the roof expands and contracts in the summer heat. Correct flashing is a mechanical, layered installation, and it’s the only fix that stops the leak rather than hiding it.
Chimney Crown Repair
Chimney Crown Repair is fixing or rebuilding the concrete top of the chimney, the sloped cap that throws water away from the flue tiles and the masonry below. You need it when the crown is cracked, pitted, separated from the flue, or sloping the wrong way, because a failing crown sends water straight down into the chimney’s interior. We chip back loose material, rebuild the slope so it drains properly, and seal the joint between the crown and the flue. Crown repair in Port St. Lucie typically runs $350 to $1,200 depending on whether the existing crown can be resurfaced or has to come off and be poured fresh. The written estimate sets the final price.
Cracks That Matter and Cracks That Don’t
A hairline crack isn’t necessarily urgent; a crack that runs the full depth or lets the flue tile wiggle is. Our camera and a visual check up top tell us which one you have, and we’ll say so.
Resurfacing Versus Rebuilding
If the crown is sound underneath, resurfacing it holds water back for years at a fraction of a rebuild. If the crown is hollow or badly broken, rebuilding is cheaper in the long run.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they can actually do, and that’s the reason a lot of repairs get handed off or done twice. When you’re choosing among chimney repair companies, look for one company that inspects, sweeps, and repairs without subcontracting, that shows you camera evidence, and that can handle liners, crowns, caps, and masonry as one job. We do all three, with HeatShield qualification for flue resurfacing and DuraFlex capability for relining, so the diagnosis and the fix stay in the same place. Repairs in Port St. Lucie range from about $200 for a minor fix up to several thousand dollars for a full reline, and the written estimate sets the price.
What to Ask Before You Hire
Ask what they’ll do if the inspection turns up a bigger problem than expected, and ask to see the evidence before any work is scheduled. A company that answers both clearly is the one worth booking.
Warnings Worth Noting
A quote given without looking up the chimney, or a repair recommended with no photos, is the thing to be cautious about. And no one should push you into a liner on the spot without showing you the cracked tile first.
Chimney Masonry Repair
Chimney Masonry Repair is the rebuilding of the brickwork, mortar joints, and chimney structure itself where water, time, and heat have broken it down. You need it when mortar is crumbling between bricks, when bricks are spalling or flaking, when the chimney leans, or when a section of the stack has loosened and a hard rain finds its way through. We tuck-point mortar joints, replace spalled brick, and rebuild damaged sections from around the roofline up, matching the existing masonry as closely as possible. Masonry work in Port St. Lucie typically runs $500 to $3,500 or more depending on how much of the stack needs rebuilding and how high up the damage runs. The written estimate sets the final price.
Tuck-Pointing the Right Way
The joints should be ground out to a proper depth and repacked with mortar matched to the brick, not smeared over the face, which traps moisture and makes the brick crack. Done correctly, the repair outlasts the brick around it.
Cracked and Spalling Brick
Spalling brick is brick that’s letting water in and breaking apart as it dries. Replacing the brick is only half the job; stopping the water that causes it is the other half, and that usually comes down to the crown and flashing.
Brands We Service
We work with a curated roster of professional-grade brands, and we know each one where it wears out. DuraFlex liners address structural and draft problems that cleaning alone can’t fix, and we install them sized to the appliance and the height of your flue. HeatShield is the system we use for flue resurfacing when a liner isn’t the answer, and we’re qualified to work it. Gelco and Famco cover the cap-and-cover category, so chimney weatherproofing uses spec-grade components rather than generic hardware-store substitutes. Olympia Chimney fills out the same family with reliable parts for caps and flue protection.
These brand names describe the products we source and install; they aren’t partnerships. If your chimney has equipment from one of these makers already, we know where the wear points are and how to repair it correctly. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains on the ceiling or chimney breast. These usually trace back to the flashing or the crown, and every rain season makes the damage worse. Left alone, it reaches the framing and the repair gets a lot bigger.
- Crumbling mortar or spalling brick. Soft mortar and flaking brick are the first signs the stack is taking on water. Once a section loosens, wind can take it down.
- A missing or damaged cap. An open flue invites rain, animals, and debris, and it lets sparks land on the roof. A cap is a small repair that prevents expensive ones.
- Smoke rolling back into the room. This points to a draft problem, often a liner issue, and it needs a proper inspection before you burn again. Don’t guess at the cause.
- A cracked or missing flue liner. This is the one to take seriously: a damaged liner lets heat and gases reach the structure of the house. Stop using the fireplace until we’ve looked at it.
Our Process, Step by Step
- 1
Book the inspection. We set a time, confirm what we’ll look at, and give you a flat price before we start so there are no surprises on the invoice.
- 2
Inspect with a camera. We run a camera down the flue and check the crown, cap, flashing, and masonry from the roof. Everything we find, you see.
- 3
Show you the evidence and the options. We walk you through what the camera found and what the repair involves. Where work can safely wait, we say so, and where it can’t, we explain why.
- 4
Do the work. Liner, cap, crown, flashing, or masonry, all handled by one company. No subcontracting the hard parts, no second appointment with a stranger.
- 5
Final check and written summary. We verify the repair, check that the flue drafts and drains as it should, and leave you a written summary of what was done.
How Much Does Chimney Repair Cost in Port St. Lucie?
Chimney repair in Port St. Lucie usually runs from about $200 for a small fix to around $5,500 for a full reline, and the written estimate sets the final price. The bigger numbers come from liner work and masonry; the smaller ones from caps, screens, and flashing reseals.
| Repair | Typical Port St. Lucie range |
|---|---|
| Chimney cap installed | $150 – $450 |
| Cap replacement | $175 – $475 |
| Flashing repair | $250 – $850 |
| Crown repair | $350 – $1,200 |
| Masonry repair | $500 – $3,500+ |
| Liner installation | $2,200 – $5,500 |
What moves the price is height, access to the roof, how much of the stack has to be opened up, and whether the fix is resurfacing or a rebuild. The way to avoid overpaying is to insist on camera evidence before any work is scheduled and to ask what can safely wait. Every estimate we give is free and comes with a written scope, so you know exactly what’s included before you agree.
Our Service Area Near Port St. Lucie
We work across Port St. Lucie and the surrounding communities, including chimney repair in River Park, White City, Indian River Estates, and North River Shores. We also cover Palm City, Stuart, Jensen Beach, and Fort Pierce. Response windows depend on the day’s schedule, and dispatch runs 7am to 7pm, Sunday through Friday. If you’re not sure whether we reach your street, call and ask; we’ll tell you straight.
Serving Port St. Lucie, FL – Our Local Coverage Area
We serve Port St. Lucie and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Port St. Lucie
Chimney repair is the fixing of the chimney’s structure and its protective parts: the flue liner, the crown, the cap, the flashing, and the masonry. It starts with an inspection to establish what’s actually wrong, and the repair follows from there. Sweeping handles creosote; repair handles the parts that hold the sweep’s work in place. We do both, so nothing gets handed off.
Most single-part repairs take a few hours: a cap, a flashing repair, or a crown resurface can often be done in one visit. A liner installation or a masonry rebuild is usually a fuller day, sometimes more when the stack needs a lot of rebuilding. We’ll give you a realistic time in the written estimate rather than a promise we can’t keep.
Typical repairs here run between $200 and $1,200, and a full liner installation runs $2,200 to $5,500, with the written estimate setting the final price. The low end covers caps and flashing; the high end covers relining and masonry. Call (844) 990-3838 for an exact quote; estimates are free.
Yes, we install DuraFlex liners and we’re qualified on the HeatShield resurfacing system, and we also work with Gelco, Olympia Chimney, and Famco components. That means the liner or the cap you have on already can be repaired by the same company that inspects it. We don’t claim those brands are exclusive to us; they’re simply the products we know best.
Same-day service is available when the schedule allows, and we dispatch Sunday through Friday, 7am to 7pm. We answer 24/7, so a call outside dispatch hours is booked into the next opening. If you have a chimney concern, call (844) 990-3838 and we’ll find the earliest slot.
We work with a manufacturer warranty on the products we install, such as DuraFlex liners, and we’ll explain in writing what that covers before you agree. Our own workmanship is set out in the written estimate so there’s nothing vague about it. If something isn’t right after we finish, call us and we’ll come back and look.
Clear the hearth and the floor in front of the fireplace, and move anything breakable away from the work area. If you can, note where you’ve seen water stains or smoke issues so we can target the inspection. Access to the roof matters most; we’ll handle the rest, and you don’t need to be home for the whole visit.
Schedule Your Chimney Repair Service in Port St. Lucie Today
Whether it’s a cap, a crown, a flashing leak, or a liner that needs looking at, the sooner we see it the smaller the fix usually is. Call (844) 990-3838 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. One company, every part of the chimney, and a no-obligation written estimate before any work begins. For more on Unity Chimney Sweep services, or to arrange chimney repair nearby, we’re one call away.
Written by the team at Unity Chimney Sweep.