Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Repair Across Port Salerno
If your fireplace is smoking back or the cap over your flue has rusted through, chimney repair in Port Salerno usually starts with a camera inspection inside the flue, and most diagnoses here come down to salt-air corrosion rather than heavy soot. We work on the older masonry stacks and the newer appliance venting that make up most of this village, and we tell you what your chimney actually needs before anything gets booked. Call (844) 990-3838. We answer 24/7.

Why Port Salerno Homeowners Call Unity Chimney Sweep for Chimney Repair
Port Salerno sits right on the Indian River Lagoon, and that changes what a chimney needs. Salt spray in the air works on metal caps and chase parts harder than it does a few miles inland, so we spend a lot of our time here on moisture damage, rusted caps, and failed crown and flashing joints. Our technicians have up to 11 years of experience with exactly this kind of repair work, and our phones are answered at any hour.
We inspect before we sweep, and we repair what we find. That means a Level 2 camera inspection comes first, and any recommendation follows the pictures. If you’ve ever been told you need a whole new liner by someone who couldn’t show you why, that’s the gap we close. We handle the sweep, the inspection, and the repair as one continuous job with a single point of contact, not three separate visits with three different vendors. You get the evidence, you get the plain explanation, and you decide. Nothing gets added to an estimate without a photo of the problem behind it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Installation in Port Salerno
Chimney Cap Installation in Port Salerno often matters more for water and pest protection than for looks, because a lagoon-front cap takes a beating from salt air and driving rain. The job means fitting a cap sized to your flue opening and the type of flue you have – clay tile, a metal chase, or a relined stack – so it seals out rain and animals without choking the draft. If your flue has been open to the weather or you’ve heard birds in the stack, a proper cap is the first fix. We work with Gelco and Olympia Chimney caps and adapters, and a typical cap installation in Port Salerno runs $250 – $550 depending on the flue size, cap style, and how much the top of the stack has to be cleaned up first.
Getting the fit right on an older stack
Older Port Salerno flues aren’t always square or perfectly level at the crown, so a cap has to be sized and seated carefully or it rattles loose or leaks around the edge. We measure the flue and the crown rather than grabbing the nearest off-the-shelf size.
Screen and spark arrestor options
The screen keeps out birds, squirrels, and wind-blown debris, and the choice comes down to mesh size and how well it holds up to salt air. Stainless holds up better than painted steel near the lagoon.
Chimney Cap Replacement in Port Salerno
Chimney Cap Replacement in Port Salerno is usually a corrosion job, not a decorative one – metal caps here rust out years ahead of the same cap inland because the lagoon air keeps a salt film on them. Replacement means pulling the failed cap and its old adapter, checking the crown and the top courses of flue tile for water damage, then fitting a new cap that seals correctly. If the cap is flaking, rusted through at the seams, or sitting crooked, it’s time. Replacement with a stainless or heavy-gauge cap typically runs $300 – $650 in Port Salerno, and it’s worth doing before the next round of hurricane-season rain gets past a failed joint and down into the smoke chamber.
Signs your cap is past saving
Rust coming through the metal, a cap that tilts or shifts when the wind hits it, and water stains down the inside of the flue are the clear ones. A cap that’s still solid but slightly loose may only need reseating, which costs less.
What the replacement covers
We remove the old cap and adapter, check the crown and flue top for spalling or cracks, and seat the new cap so it seals out rain. If the crown has failed underneath, we’ll flag it and quote that separately.

Trusted Brands We Service in Port Salerno
We work with a curated roster of professional-grade brands: DuraFlex for liner systems, HeatShield for flue resurfacing, Gelco and Olympia Chimney for caps and covers, and Famco where the spec calls for it. For Port Salerno homes with an older clay-tile or unlined stack, HeatShield and DuraFlex are the two that let us resurface or reline a flue rather than tell you the only option is a full rebuild. Those brands are the reason we can take a deteriorated flue from diagnosis to a finished, properly vented system without handing the hard part to somebody else.
See the difference
Before
After
Before
After
Before
AfterCommon Chimney Repair Problems We See in Port Salerno Homes
- Clay-tile flues venting the wrong appliance. A gas insert or other appliance tied into an old stack that was never designed for it is common here, and it shows up as draft problems and a real carbon-monoxide risk. It’s an inspection problem first, and we check it with a camera before quoting a liner.
- Salt corrosion on caps and chase parts. The lagoon air keeps caps and metal chase components wet with a salt film, so they rust ahead of the inland schedule. A cap that looks fine from the ground can be through at the seams when we get up close.
- Failed crowns and flashing joints. Hurricane-season wind-driven rain gets into the crown and flashing every year, and water reaches the smoke chamber and firebox long before a homeowner notices. Moisture damage like this gets misread as a sweeping problem when the real fix is resealing.
- Spalling mortar and joint gaps in older masonry. Mid-century CBS and cracker-style stacks in the older core of Port Salerno often have soft mortar joints and loose brick. Repointing and tuckpointing fix those before the brick itself starts to go.
Pricing for Chimney Repair in Port Salerno, FL
What a repair costs here follows the job, so we quote from the written estimate after we’ve seen inside the flue. Repointing and tuckpointing on a typical stack runs $400 – $1,200, chimney waterproofing for salt-exposed masonry runs $350 – $800, flashing repair runs $300 – $750, and a HeatShield flue resurfacing runs $1,200 – $2,800 depending on flue length and condition. Cap work sits in the ranges above. What moves the price is the condition of the crown, whether the flue needs relining, and how accessible the roof is. The estimate is free, the numbers are ours and not a range we’ll revise on arrival, and anything that can safely wait a season, we’ll tell you it can wait.
We Also Serve Cities Near Port Salerno
We take the same repair and inspection work to homeowners in Stuart, North River Shores, Palm City, and Hobe Sound, and the salt-air corrosion that drives repairs in Port Salerno is just as real up and down the lagoon. If you’re nearby and your cap is failing or your stack is smoking back, call us. Read more about Port Salerno and our Chimney Repair.
Serving Port Salerno, FL – Our Local Coverage Area
We serve Port Salerno and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Repair in Port Salerno
Not necessarily, but it has to be inspected before you light it. A clay-tile flue in an older Port Salerno home is often unlined or has spalling mortar and joint gaps that a camera will show clearly. If the tile is intact and the appliance matches the flue, no liner is needed. If there’s a gap or the flue was never lined for the appliance now venting into it, we’ll show you the video and explain the liner options, including HeatShield resurfacing or a DuraFlex liner. Call (844) 990-3838 for a free estimate.
Salt. The Indian River Lagoon air keeps a fine salt film on metal, and that film holds moisture against the cap, so it rusts years ahead of a cap a few miles inland. Galvanized caps fail fastest; stainless holds up far better. When we replace a cap on a lagoon-side stack, we check the crown and the top of the flue at the same time, since water that got past the failed cap often did damage underneath. Call (844) 990-3838 for a free estimate.
Because most chimney problems here aren’t about soot. They’re about water and salt. A Port Salerno chimney that sees light use can still have a rusted cap, a failed crown, or a flashing joint that lets rain into the smoke chamber, and an old flue venting a gas insert that was never designed for it. That’s why we inspect with a camera even on a stack that’s hardly been used. Call (844) 990-3838 for a free estimate.
It’s often a repair, not a quirk of draft. Smoke rolling back in a Port Salerno home usually traces to a rusted or corroded cap, a failed crown letting water into the flue, or a damper that no longer seats properly. A Level 2 camera inspection shows which one it is. Once we can see the cause, the fix is usually a cap, a crown reseal, or relining – and we show you the picture before quoting it. Call (844) 990-3838 for a free estimate.
You ask to see the camera evidence, and a real chimney professional will show it to you. That’s how we work here: nothing is recommended without a photo or video of the problem, so you can judge the repair yourself. If the flue is sound, we say so, even when that means less work for us. If a repair can safely wait a season, we tell you. Call (844) 990-3838 for a free estimate.
Written by the team at Unity Chimney Sweep.